W11 Three-Roller Mechanical Metal Sheet Rolling Machine
The elevation movement of the upper roller is realized by the auxiliary motor through the auxiliary reducer, which drives worm and worm wheel under the left and right roller bearing to move automatically, makes the steel wire nut which is fixed on the worm wheel rotating, and completed by up and down movement of ball bearing screws accordingly.
The offloading device is used after the round cylinder has been finished. Before leaving the left bearing seat, raises the upper roller to standard height, and make the upper roller stop with balance pull rod at the bottom of upper roller. Then draw out pin shaft on the tilting bearing seat, overturn the tilting bearing seat, then the coiled product can emerge from one end of the upper roller.
The main components are: three 45 steel forged rollers, HRC3545, support frame is welded, process after being welded, the lower pallet is a welded part. Ball bearing screw and worm gear are 45 steel forged parts.
Electrical parts is adopted famous apparatus, steady performance, durable, safe and reliable, operates conveniently.
(variable models)
Max rolling thickness(mm) 6 - 60
Max rolling width (mm) 1500 - 3200
Plate yield limit (mPa) 265
Minimum coil loaded diameter (mm) 380 - 2000
Under shaft diameter (mm) 210 - 800
Upper shaft diameter (mm) 180 - 560
Two lower shaft center distance (mm) 210 - 800
W12 Four-Roller Hydraulic Metal Sheet Rolling Machine
This machine is a hydraulic four-roller bending machine and used to do pre-bending the end of plate, rolling it into round, cone and other shapes. Four roller bending machine is recognized as the fastest, most accurate, most likely to use the machine.
The rest of the straight edge segment is greatly reduced-only one end of the board is fed. There is also the source of its outstanding pre bending capacity: clip point completely fell on the edge of the plate.
Automatic feeding material-with the feed side of the opposite side of the rear roll, can be used as a rear stop material, the plate immediately into a right angle parallel position, sheet metal flat easy, single operation can.
After the correction of the plate, the upper and lower parts of the middle of the clip to the middle of the clamp, so it is safe and easy to operate, there is no risk of sheet slippage.
In the front of the plate, the diameter of the cylinder can be made immediately. Because only in the machine tool side need to enter the space can be used, which means that the operation of the machine tool is less space.
After the cylinder volume is made, the end of the roll is made. A cylinder by bending forming.
Taper coil is easy, can be rolled to the biggest angle of 30 degree cone. The side roll is inclined to determine the angle of the cone, and the center of the lower center can also tilt, clamp and drive plate.
In the rolling process, ensure the plate clamping and driving, four roller bending machine is the single most applicable on the NC and CNC systems through effective control of the bending machine.
In the cylinder after rolling, rolling on the tail edge (four roller bending machine can bend ahead, can also bend back). A cylinder by bending forming.
(variable models)
Max bending thickness(mm) 4 - 60
Pre bending thickness(mm) 3.5 - 48
Max rolling Length 2050 - 3150
Plate yield limit (mPa) 245
Top roller diameter (mm) 160 - 670
Bottom roller diameter (mm) 140 - 620
Side roller diameter (mm) 120 - 520
Power (kW) 3 - 75
W12-8X2000 4-roller Rolling Machine with Side and Vertical Support
W12-8X2000 Hydraulic CNC Rolling Machine with Side and Vertical Support. HARSLE CNC rolling machine is a kind of machine that uses rollers to bend and shape the plate. It rolls the rollers through the external forces such as hydraulic pressure and mechanical force so that the plate can be pressed and bent or rolled and shaped, and it can make different shapes of parts such as oval parts, curved parts and barrel parts, which is a very important kind of processing machine. The supporters above and on both sides of the machine are optional, supporters can move with the operation lever adjustment, which can assist longer or heavier plate forming work in the process of rolling work.
(variable models)
Max bending thickness(mm) 4 - 60
Pre bending thickness(mm) 3.5 - 48
Max rolling Length 2050 - 3150
Plate yield limit (mPa) 245
Top roller diameter (mm) 160 - 670
Bottom roller diameter (mm) 140 - 620
Side roller diameter (mm) 120 - 520
Power (kW) 3 - 75
info@anytek.ae
Dubai
Al Muteena BC RES 1072 OFFICE 4C-06
Trade license:22780
